|
|
| (77 intermediate revisions by 4 users not shown) |
| Line 1: |
Line 1: |
| ==Disclaimer==
| | This manual has been superseded (replaced) by a PDF: |
|
| |
|
| This description is meant to inform the community how to layout
| | http://svn.smallangles.net/trac/canSAS/browser/1dwg/tags/v1.0/doc/cansas-1d-1_0-manual.pdf?format=raw |
| the information within the XML files. However, should the
| |
| information in this document and the [[cansas1d.xsd | canSAS 1D SAS XML Schema]]
| |
| differ, the XML Schema will be deemed to have the most correct description
| |
| of the standard.
| |
| | |
| ==General Layout of the XML Data==
| |
| | |
| ===required XML file header===
| |
| <pre>
| |
| <?xml version="1.0"?>
| |
| <SASroot version="1.0"
| |
| xmlns="http://www.smallangles.net/cansas1d"
| |
| xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
| |
| xsi:schemaLocation="http://www.smallangles.net/cansas1d/
| |
| http://www.smallangles.net/cansas1d/1.0/cansas1d.xsd"
| |
| >
| |
| </pre>
| |
| | |
| ===alternative XML file header (referencing a stylesheet)===
| |
| <pre>
| |
| <?xml version="1.0"?>
| |
| <?xml-stylesheet type="text/xsl" href="example.xsl" ?>
| |
| <SASroot version="1.0"
| |
| xmlns="http://www.smallangles.net/cansas1d"
| |
| xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
| |
| xsi:schemaLocation="http://www.smallangles.net/cansas1d/
| |
| http://www.smallangles.net/cansas1d/1.0/cansas1d.xsd"
| |
| >
| |
| </pre>
| |
| | |
| ===overall file: layout of SASroot===
| |
| | |
| After the XML header, the root element of the file is SASroot which
| |
| contains one or more SASentry elements, each of which describes
| |
| a single experiment (data set, time-slice, step in a series, new
| |
| sample, etc.). Details of the SASentry element are also
| |
| shown in the next figure.
| |
| | |
| [[Image:cansas1d-v1-1-SASroot.png | block diagram at SASroot level]]
| |
| | |
| ===block diagrams===
| |
| There are other block diagrams available:
| |
| *[[cansas1d-v1-1-SASroot.png | SASroot]]
| |
| ** SASentry (data set, time-slice, step in a series, new sample, etc.)
| |
| ***Title (for this particular SASentry)
| |
| ***Run (run number or ID number of experiment)
| |
| ***[[cansas1d-v1-2-SASdata.png | SASdata]] (this is where the reduced 1-D SAS data is stored)
| |
| **[[cansas1d-v1-3-SASsample.png | SASsample]]
| |
| **[[cansas1d-v1-4-SASinstrument.png | SASinstrument]]
| |
| ***[[cansas1d-v1-5-SASsource.png | SASsource]]
| |
| ***[[cansas1d-v1-6-SAScollimation.png | SAScollimation]]
| |
| ***[[cansas1d-v1-7-SASdetector.png | SASdetector]]
| |
| **[[cansas1d-v1-8-SASprocess.png | SASprocess]] (for each processing or analysis step)
| |
| ** SASnote (anything at all)
| |
| * [[cansas1d-v1-9-full.png | full block diagram]]
| |
| | |
| ==Definition of terms==
| |
| | |
| See [[cansas1d_definition_of_terms]] for the complete list of terms (XML elements and XML attributes) in the canSAS 1-D standard.
| |
| | |
| ==rules==
| |
| # Q=(4 π / λ) sin(θ) <br> where λ is the wavelength of the radiation and 2θ is the angle through which the detected radiation has been scattered.
| |
| # units to be given in standard SI abbreviations (eg, m, cm, mm, nm, K) with the following exceptions:
| |
| ##um=micrometres
| |
| ##C=celsius
| |
| ##A=Angstroms
| |
| ##percent=%.
| |
| ##fraction
| |
| ##a.u.=arbitrary units
| |
| ##none=no units are relevant (such as dimensionless)
| |
| # where reciprocal units need to be quoted the format shall be "1/abbreviation"
| |
| # Unicode characters MUST NOT be used
| |
| # axes:
| |
| ##z is along the flight path (positive value in the direction of the detector)
| |
| ##x is orthogonal to z in the horizontal plane (positive values increase to the right when viewed towards the incoming radiation)
| |
| ##y is orthogonal to z and x in the vertical plane (positive values increase upwards)
| |
| #angles:
| |
| ##roll is about z
| |
| ##pitch is about x
| |
| ##yaw is about y
| |
| | |
| ==Validation of XML against the Schema==
| |
| # open browser to: http://www.xmlvalidation.com/
| |
| # paste content of candidate XML file (with reference in the header to the XML Schema as shown above) into the form
| |
| # press <validate>
| |
| # paste content of [[cansas1d.xsd]] XSD file into form and press <continue validation>
| |
| # check the results
| |
